0000139882 00000 n Valid values for datetime_format are iso8601 and epoch. 0000410990 00000 n There is an issue with the meter measurements. According to the IQ Envoy manual this is possible if the user wants revenue-grade production metering. measure resistance from black wire at lgm connector (while disconnected) to ground behind side panel inside rear cargo area. So I've had my envoy setup for 5 years now no issues. I agree a better solution would be to have additional parameters. All dates are in the timezone of the requested system. I will make a capture tomorrow when it's light and the system is actualually producing. There are 1609 meters in a statute mile. Have an assistant crank the engine for a few seconds while you watch the meter's readout. What does the "Envoy Failure" message mean? - Enphase Support In metric, 1 meter is 100 centimeters and a kilometer is 1000 meters. Here is the output of envoy_reader from various Envoys. WebThe IQ Envoy uses readings from CTs to report measurement data for energy production and energy consumption. It was like this for a But have to think about current users. Enphase consumption CT measurement problem. Also would need to check this behavior on newer firmware such as D5.0.49 (77afa8) to see what happens when metering is not setup and if the /production.json page returns valid data or not. If the total duration requested is more than one month, returns one month of intervals. This page was generated at 03:27 AM. Install a phase coupler on the load side of the over-current protection device. All rights reserved. If some of your microinverters have stopped reporting to the Envoy, youll see a problem message like this: Click the link in the message to see which microinverters are not reporting and their location in your array: Learn what you can do if some of your microinverters have stopped reporting. One case that is not handled, if you want the inverters current production and WH lifetime production, with metering turned on, you can only get that from production.json. Web4.14.23 Scheduled Maintenace. I'll have to look into this one a bit. From what I have seen on the Envoy IQ it only accumulates WH totals (today and 7 day) in the eim production structure of production.json WHEN CT metering is enabled. Why not use actual values (with decimals, when reported)? To troubleshoot this, check CT orientation and leads, compared with voltage measurements using your regional CT You may change the format of returned date and time values by passing the query parameter datetime_format on any endpoint that returns date or time values; for example. Well occasionally send you account related emails. Could this have been fixed in a later firmware revision? metered_production_readingtime No Home Assistant will not get fully updated automatically. Part number: 800-00554-r03, Envoy Fyi: There exist 3 different Envoy-S models: I have the Envoy-S Metered Multiphase (EU) SKU: ENV-S-WM-230. Sometimes a request cannot be processed because the requested dates are invalid for the the system in question. How to fix a 'Meter Issue' system error message? - Support In addition, the Envoy-S Metered provides revenue-grade production data and allows for the monitoring of a sites energy load, thus offering significant advantages over other PV system monitoring equipment. Users can access energy production and consumption data through Enphase Enlighten cloud based monitoring software. Like I said I'm still thinking about it and weighing the pros and cons. Note: If a system does not include a given device type, that key is left out of the returned hash. 0000015743 00000 n My 8x320W=2.56 kw mono array gets the IQ6+ inverters running at pf=1 at 700 VA. Envoy S Production data is not read / read incorrectly when current transformers are not enabled/installed [bug], https://thecomputerperson.wordpress.com/2016/08/03/enphase-envoy-s-data-scraping/#comment-5838, Add production_readingtime and consumption_readingtime output parameters, Add consumption_ct_metering_enabled and production_ct_metering_enabled output parameters, Support reading values of consumption and production per phase, The envoy is configured without CT metering and the user wants WH totals for today and 7 days which aren't available in. Enlighten declares a Meter Issue () system status when it detects a possible problem with the CT or storage measurements. Today is medium overcast so that is adding to low production. Requests for times that do not fall on the 15-minute marks are rounded down. 0000078331 00000 n 0000161309 00000 n /api/v1/production does not contain "readingTime" but /production.json "type": "inverters" does. Sometimes, but not The rmsVoltage may actually be measured by the Envoy, but without any CT's installed, the rmsCurrent value apparently is a bogus value(?). An Enphase team member may follow up with you about your feedback. Clients of the API are expected to do the same: Be order-agnostic, and ignore unknown response values. Here is heavy overcast at the end of the day with sun low and far to the side of the array. Envoy Mobile troubleshooting FAQ | Envoy Help Center And when envoy_reader reads its data from the "eim" section shouldn't that be done for each phase separately and then summed to get totals for all 3 phases? Envoy WebEnvoy-S Standard Compatible Microinverter (s) M215, M250 Primary Use Residential & Small Commercial AC Supply 230 VAC, 50 Hz Production Metering 5% accurate microinverter measurements Warranty Length 5 years Designed for an outdoor enclosure Integrated Wi-Fi & Mobile Connect Ready Consumption Monitoring & Storage Ready avh]O(ar /I;}z*',)RsB$F8$tE)>}0.B "sk]a/E+sQWTM/Na>GGqJRCX?? Here's my output. If ct_metering_consumption is false then the. According to the Envoy-S Metered Multiphase Installation manual there are 3 CTs installed on the Production and Consumption sides. metered_consumption_readingtime, How about simplifying When True the Envoy should be handled as endpoint_type "PC", when False as endpoint_type "P". My blue bars show production and yours appear to show consumption. (for recent Envoy models that output production.json).
Darrin Vincent Daughter,
Tom Thumb Vehicle Registration Dallas County,
Andray Domise Name Change,
Abandoned Railroad Tunnels In West Virginia,
Vivian Orlen Superintendent,
Articles I